🌼为赶不上打标机通过使用期，提高 装配通过率和无缺率，应该削减错误率。现将我单位打标机经常确保及安养基本常识与艺术大师分享赚钱。
𒐪In order to prolong the service life of the jet printer, improve the utilization rate and intact rate of the equipment, and reduce the failure rate. Now we share our daily maintenance and maintenance knowledge with you.
一、喷码机平常利用注重事变：
1. Notices for the daily use of jet printers:
𝓰1、因喷码器通过的uv墨水和精提剂很是贸然熄火，言于须在杰出贡献透气处打理喷码器，久别火源计划、火花和如何消除静电。
🅠1. Because the ink and diluent used in the jet printer are very easy to burn, it is necessary to place the jet printer in a well-ventilated place, away from fire, flame and static electricity.
2、避免遗失uv油墨、洗濯剂水浸泡过的碎布和碎纸带在手持喷码机旁。
⛎2. Do not leave any ink, cloth and paper pieces soaked in detergent beside the printer.
♚3、 不能在手持打标机周边围吸二手烟，应吊式“抵制炊火”和“易燃性uv墨水”标识在手持打标机周边围。
𒊎3. Smoking is strictly prohibited near the printer. The signs of "No Fireworks" and "Flammable Ink" should be hung near the printer.
4、在激光打码机4周设置二氧化物碳灭冷兵器（反衬远隔10米）。
🔯4. Place a carbon dioxide fire extinguisher near the jet printer (the longest distance is 10 meters).
二、喷码主轴电机气毗连注重质量事变
✱II. Notices for Electrical Connection of Jet Coder
🐠1、 接完220V这一项供电（含地线），不得不利用率原厂装配的供电线，毗连到牢靠的、提升装置有地线的供电插座面板上。
🦂1. When connected to 220V single power supply (including ground wire), the original power supply cable must be used and connected to a fixed power socket with ground wire.
﷽2、 地线的毗连需求严格遵守有关于按照。要是地线打丈不良的，有就能组成打标机电脑主板的伤害或出现另外的埋伏的风险。
𒅌2. The connection of ground wires must comply with the relevant regulations of the state. If the ground wire contact is not good, it may cause damage to the printer motherboard or other potential hazards.
三、平时养护养护着重事变
3. Daily maintenance matters needing attention
1. 灵活运用喷码器uv油墨、浓缩造成剂时对劝解配戴消退眼镜镜片。
൲1. It is absolutely forbidden to wear contact lenses when using ink and diluent of jet printer.
2. 当提升喷墨墨水或浓缩提炼剂操控时，倡仪书利于抗相转移催化剂皮手套和卫生防护镜。
♋2. Anti-solvent gloves and protective goggles are recommended when adding ink or diluent.
3. 打码机大多数医养程序运行以下的：
🍌3. The daily maintenance process of the jet printer is as follows:
背景激光打码机呵护安养首就是线路、喷头型号安养：
🦄Maintenance of Beijing Printer is mainly pipeline and nozzle maintenance.
♑a) 蓝蓝油墨版本更新系统：先将线路里的蓝蓝油墨全数抽暇，沉淀剂倒入蓝蓝油墨罐使用1h后全数 排斥，立即干预沉淀剂使用0.5h后全数排斥，干预原厂装配的蓝蓝油墨。呼吁机械厂每再生合理利用一个月终止多次蓝蓝油墨版本更新系统，保证装配使用翻倍不减。（抽取的废弃物不呼吁二级再生合理利用，防范止达成线路梗塞） a) 喷咀洗濯：对不兼有会去主动洗濯作用的喷码器，呼吁一天到晚电源开关机时洗濯，以 事关机拥有高道德的网页打印没想到。在喷咀以下筹划储槽，用共公洗桶装入沉淀剂，预瞄雾炮、充电器极、测量极、直流电偏转板上的墨渍终止洗濯，重要性不必让沉淀剂溅进口清关眼及皮肤图片，洗濯清扫后，拿纸巾将喷咀各不件的洗濯剂洗净。
𓃲(a) Ink renewal: first, all the ink in the pipeline is exhausted, diluent is injected into the ink tank for 1 hour, then all the ink is discharged after adding diluent for 0.5 hours, and then the original ink is added. It is suggested that the machine be updated once a year to ensure more stable operation of the equipment. (Waste liquid extracted is not recommended for secondary use in order to avoid pipeline blockage.) a) Sprinkler cleaning: For the sprinkler without automatic cleaning function, it is recommended that the machine be cleaned when switched on and off every day to ensure high quality printing effect. First, place the container under the sprinkler head, fill the diluent with a special bottle, clean the ink stains on the nozzle, charging electrode, detection electrode and high-pressure deflection board. Take care not to let the diluent splash into the eyes and skin. After cleaning, wipe the cleaning agent of all parts of the sprinkler head with a paper towel.
ಌb) 调济墨线：若发明家墨线背离收受移交器，已停喷口买通，用公共洗瓶插足少 许浓缩液剂至喷口帽，频烦买通3次开始的，如墨线一支在统一性整体素质则需已停奖金调养喷腔。墨线规范性：对着收受移交器查看苹果手机，墨线喷入收受移交器二分中之一处且略左。（侧看墨线在收受移交器正中间间）
✨B) Adjust ink line: If the ink line deviates from the reclaimer, the nozzle should be opened first, a little diluent should be added to the nozzle cap with a special washing bottle, and the nozzle cap should be opened three times or so repeatedly. If the ink line is always in the same position, the nozzle cavity should be adjusted artificially. Ink standard: Looking at the recycler, ink is sprayed into one third of the recycler and slightly left. (Look sideways at the ink line in the middle of the receiver)
🔜二）手持打标机永劫间断电后的养护 随便次断电，不顾过程中是否，只需该手持打标机在每日内开启设备暖机2次，并摊开墨线合适接续暖机或胶印油墨发布一种一小时，如此便也能用有多少次短断电更换永劫间的断电。
💧2) Maintenance of any downtime of the jet printer after a long downtime, regardless of the length of time, as long as the jet printer runs twice a week, and opens the ink line to run continuously or ink updates for at least one hour, it can replace the long downtime with several short downtime.
1）打码机停用阶段为8-60天：对喉管和花洒头中止一次性洗濯，花洒头朝上安装，以避免墨囊离交柱。
♚1) Inkjet printer shutdown time is 8-15 days: the throat and nozzle are cleaned once, the nozzle is placed upward to prevent ink reflux.
ไ2）喷码器熄火之后跨跃5天：这段时间必须要将机械厂内的打印墨汁的排放后参与精炼剂运行，终了后把打印机喷头朝上拟定，以避免打印墨汁出液。
𓂃2) The stop time of the printer is more than 15 days. At this time, the ink in the machine must be discharged and run with diluent. After that, the sprinkler head should be placed upward to prevent the ink from flowing back.
ꦛ3）永劫间停此时后初始化激光打码机注重细节事变 停此时8-30天会激光打码机的初始化，若有目前，审单两下墨线不便性。停此一下420分钟的高压喷嘴买通。
꧑3) Start the printer after a long downtime. Notes: Start the printer 8-30 days after the downtime. If necessary, check the stability of the ink line. Make a 5-minute nozzle pass.
4)停止那时候转变30天
4) Over 30 days of downtime
🍰将线路中的印刷印刷油墨排净。参与溶缩剂正常使用小时候，疏浚因永劫间进行时而梗塞的线路。溶缩剂正常使用时可进行一个分之五钟的喷水嘴买通。溶缩剂正常使用终了第三排净线路，参与新印刷印刷油墨，再买通喷水嘴3min使墨线战略地位倍增相同。
ꦿEmpty the ink in the pipeline. Add diluent and run for one hour to dredge the blocked pipeline due to long shutdown. When the diluent is running, the nozzle can be opened for 5 minutes at a time. After the diluent is running, the drainage pipe is emptied, new ink is added, and the nozzle is opened for 3 minutes to make the ink line position more stable.
ꦑ5) 激光打码机保护英文保养时间间隔。 每半个月大对激光打码机管道阀门关闭程序次查抄，是否是老化测试、议论是否是晃动 改换过虑器。该操控视区域场景而定，如烟尘较高最低时间间隔4个月大改换次，通常区域场景下时应时间间隔1俩个月大关闭程序次。物理外界除尘设备。该操控最低时应时间间隔4个月大关闭程序次。
ᩚᩚᩚᩚᩚᩚᩚᩚᩚ𒀱ᩚᩚᩚ5) Maintenance cycle of jet printer. Every 15 days, check the pipeline of the jet printer, whether it is ageing, whether the joints are loosened and the filters are replaced. The operation depends on the environment. If the dust is large, it should be replaced at least every four months. Normally, it should be done every 12 months. Dust removal inside the machine. The operation should be performed at least once every 1 month.
四、手持喷码机耗材类的运用和手机截图了解事变
𒆙IV. Notices for Use and Maintenance of Consumables for Printers
🧜1、打码机再生利用的耗损品发挥性强，永久保存时，应不超35度，可以防止高低温，远离阴燃、热环境，必需密封盖杰出贡献并存贮在荫凉通风处（黑客入侵性好的厚壁铁柜体保存）。
ꦗ1. The consumables used in the jet printer are highly volatile. They should be kept below 35 degrees, avoid high temperature and keep away from fire and heat sources. They must be well sealed and stored in a shady and ventilated place (in a thick-walled iron cabinet with good sealing).
2、喷码器的耗损品的质保期是年。
﷽2. The shelf life of consumables of jet printer is one year.
3、打标机的耗损品严酷相应厂家采取，不得当采取编辑品，不燃会给裝备生成严重风险。
🍌3. The consumables of the jet printer should be strictly used in accordance with the brand, and no substitute should be used, otherwise serious damage will be caused to the equipment.